The August MVUS meeting will be the annual picnic, measurement event and
election of officers. The normal monthly meeting at MCL will not be held in
August. The picnic will be on Saturday August 24 starting at about 11 AM at
Daun Yeagley's home. Daun's GPS and street address:
39.506953, -83.862522
1353 Gurneyville Rd
Wilmington Oh 45177
Bring a side dish or dessert for maybe 6 people. Burgers, brats and drinks
courtesy of MVUS.
If you want any testing done, contact N8ZM at n8zm@mvus.org. He needs to
know what you want to test and the frequency range. Preamps, antennas,
power amps. SWR bridges, power supplies, meters, whatever. Just let Tom
know so we can have the right test gear available.
Adapters for anything other than N, PL259, or SMA would be helpful.
Anything upto 6 GHz is easy above that advanced notice is definitely needed.
Bring a couple chairs as well.
If you need additional details contact Tom Holmes or Jim Bacher.
Jim
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
On Jul 18, 2019, at 9:22 PM, Jim Bacher via mvus-list mvus-list@lists.febo.com wrote:
The August MVUS meeting will be the annual picnic, measurement event and
election of officers. The normal monthly meeting at MCL will not be held in
August. The picnic will be on Saturday August 24 starting at about 11 AM at
Daun Yeagley's home. Daun's GPS and street address:
39.506953, -83.862522
1353 Gurneyville Rd
Wilmington Oh 45177
Bring a side dish or dessert for maybe 6 people. Burgers, brats and drinks
courtesy of MVUS.
If you want any testing done, contact N8ZM at n8zm@mvus.org. He needs to
know what you want to test and the frequency range. Preamps, antennas,
power amps. SWR bridges, power supplies, meters, whatever. Just let Tom
know so we can have the right test gear available.
Adapters for anything other than N, PL259, or SMA would be helpful.
Anything upto 6 GHz is easy above that advanced notice is definitely needed.
Bring a couple chairs as well.
If you need additional details contact Tom Holmes or Jim Bacher.
Jim
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
I'm sure we can gin up a setup to test it. I've got power meters and
loads up to 100W. I could press my IC-7300 into service for a source,
but if you want to bring a rig that would be fine also.
Daun
Daun E. Yeagley II, N8ASB
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
On Jul 18, 2019, at 9:22 PM, Jim Bacher via mvus-list mvus-list@lists.febo.com wrote:
The August MVUS meeting will be the annual picnic, measurement event and
election of officers. The normal monthly meeting at MCL will not be held in
August. The picnic will be on Saturday August 24 starting at about 11 AM at
Daun Yeagley's home. Daun's GPS and street address:
39.506953, -83.862522
1353 Gurneyville Rd
Wilmington Oh 45177
Bring a side dish or dessert for maybe 6 people. Burgers, brats and drinks
courtesy of MVUS.
If you want any testing done, contact N8ZM at n8zm@mvus.org. He needs to
know what you want to test and the frequency range. Preamps, antennas,
power amps. SWR bridges, power supplies, meters, whatever. Just let Tom
know so we can have the right test gear available.
Adapters for anything other than N, PL259, or SMA would be helpful.
Anything upto 6 GHz is easy above that advanced notice is definitely needed.
Bring a couple chairs as well.
If you need additional details contact Tom Holmes or Jim Bacher.
Jim
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
I have repaired these before. There are, or should be trimmer pots
inside to adjust the needle readings.
No need to send it off for re-cal.
I did a quick search and I found the calibration document:
www.radiomanual.info/schemi/ACC_instrument/Daiwa_CN-801V_serv.pdf
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=2ahUKEwizgKaErcHjAhWGMd8KHVCjCQkQFjABegQIAhAC&url=http%3A%2F%2Fwww.radiomanual.info%2Fschemi%2FACC_instrument%2FDaiwa_CN-801V_serv.pdf&usg=AOvVaw1wjeAjrs2P8pV27q-7bmuc
Jan N8CBX
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
Thanks, Jan
Pretty much the procedure I expected, and this adds what pot does what!
Daun
Daun E. Yeagley II, N8ASB
On 7/19/2019 12:04 PM, Jan Servaites via mvus-list wrote:
I have repaired these before. There are, or should be trimmer pots
inside to adjust the needle readings.
No need to send it off for re-cal.
I did a quick search and I found the calibration document:
www.radiomanual.info/schemi/ACC_instrument/Daiwa_CN-801V_serv.pdf
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=2ahUKEwizgKaErcHjAhWGMd8KHVCjCQkQFjABegQIAhAC&url=http%3A%2F%2Fwww.radiomanual.info%2Fschemi%2FACC_instrument%2FDaiwa_CN-801V_serv.pdf&usg=AOvVaw1wjeAjrs2P8pV27q-7bmuc
Jan N8CBX
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them
but the meter is way off ( think the user before me started turning
pots )
Needs to only be close or should this be just sent back to factory
to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline
close to there’s again I just use this for reflective power
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
Hi Brett...
We just need a couple of transmitters(Hf and vhf), a dummy load and a known good wattmeter(I have a Bird). That should do it.
Don’t know why diode would pop unless way over powered.
From Tom Holmes, N8ZM
On Jul 19, 2019, at 11:40 AM, Brett Scott via mvus-list mvus-list@lists.febo.com wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
<image1.jpeg>
On Jul 18, 2019, at 9:22 PM, Jim Bacher via mvus-list mvus-list@lists.febo.com wrote:
The August MVUS meeting will be the annual picnic, measurement event and
election of officers. The normal monthly meeting at MCL will not be held in
August. The picnic will be on Saturday August 24 starting at about 11 AM at
Daun Yeagley's home. Daun's GPS and street address:
39.506953, -83.862522
1353 Gurneyville Rd
Wilmington Oh 45177
Bring a side dish or dessert for maybe 6 people. Burgers, brats and drinks
courtesy of MVUS.
If you want any testing done, contact N8ZM at n8zm@mvus.org. He needs to
know what you want to test and the frequency range. Preamps, antennas,
power amps. SWR bridges, power supplies, meters, whatever. Just let Tom
know so we can have the right test gear available.
Adapters for anything other than N, PL259, or SMA would be helpful.
Anything upto 6 GHz is easy above that advanced notice is definitely needed.
Bring a couple chairs as well.
If you need additional details contact Tom Holmes or Jim Bacher.
Jim
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
Jan...
You need to come out to the picnic!
From Tom Holmes, N8ZM
On Jul 19, 2019, at 12:04 PM, Jan Servaites via mvus-list mvus-list@lists.febo.com wrote:
I have repaired these before. There are, or should be trimmer pots inside to adjust the needle readings.
No need to send it off for re-cal.
I did a quick search and I found the calibration document:
www.radiomanual.info/schemi/ACC_instrument/Daiwa_CN-801V_serv.pdf https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=2ahUKEwizgKaErcHjAhWGMd8KHVCjCQkQFjABegQIAhAC&url=http%3A%2F%2Fwww.radiomanual.info%2Fschemi%2FACC_instrument%2FDaiwa_CN-801V_serv.pdf&usg=AOvVaw1wjeAjrs2P8pV27q-7bmuc
Jan N8CBX
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
Holly smokes Jan !
You are GREAT !! Thank you !
But How are we going to tell Tom Holmes he is no longer needed ?
I guess we won’t have to wait him up after the meal to do this lol lol
I love this group and Thank you all for all your Knowledge and sharing it . I plan on being there this year .
Sent from my iPhone
On Jul 19, 2019, at 12:48 PM, Tom Holmes via mvus-list mvus-list@lists.febo.com wrote:
Jan...
You need to come out to the picnic!
From Tom Holmes, N8ZM
On Jul 19, 2019, at 12:04 PM, Jan Servaites via mvus-list mvus-list@lists.febo.com wrote:
I have repaired these before. There are, or should be trimmer pots inside to adjust the needle readings.
No need to send it off for re-cal.
I did a quick search and I found the calibration document:
www.radiomanual.info/schemi/ACC_instrument/Daiwa_CN-801V_serv.pdf https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=2ahUKEwizgKaErcHjAhWGMd8KHVCjCQkQFjABegQIAhAC&url=http%3A%2F%2Fwww.radiomanual.info%2Fschemi%2FACC_instrument%2FDaiwa_CN-801V_serv.pdf&usg=AOvVaw1wjeAjrs2P8pV27q-7bmuc
Jan N8CBX
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
Brett...just remember I’m the guy who does the cooking.
From Tom Holmes, N8ZM
On Jul 19, 2019, at 1:30 PM, Brett Scott kd8rhs@att.net wrote:
Holly smokes Jan !
You are GREAT !! Thank you !
But How are we going to tell Tom Holmes he is no longer needed ?
I guess we won’t have to wait him up after the meal to do this lol lol
I love this group and Thank you all for all your Knowledge and sharing it . I plan on being there this year .
Sent from my iPhone
On Jul 19, 2019, at 12:48 PM, Tom Holmes via mvus-list mvus-list@lists.febo.com wrote:
Jan...
You need to come out to the picnic!
From Tom Holmes, N8ZM
On Jul 19, 2019, at 12:04 PM, Jan Servaites via mvus-list mvus-list@lists.febo.com wrote:
I have repaired these before. There are, or should be trimmer pots inside to adjust the needle readings.
No need to send it off for re-cal.
I did a quick search and I found the calibration document:
www.radiomanual.info/schemi/ACC_instrument/Daiwa_CN-801V_serv.pdf https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=2ahUKEwizgKaErcHjAhWGMd8KHVCjCQkQFjABegQIAhAC&url=http%3A%2F%2Fwww.radiomanual.info%2Fschemi%2FACC_instrument%2FDaiwa_CN-801V_serv.pdf&usg=AOvVaw1wjeAjrs2P8pV27q-7bmuc
Jan N8CBX
On 7/19/2019 11:40 AM, Brett Scott via mvus-list wrote:
Tom or anyone this meter blow out the Signal diode I’ve replace them but the meter is way off ( think the user before me started turning pots )
Needs to only be close or should this be just sent back to factory to be calibrated????
Or does any one have one like this CN-801
1.8 to 200MHZ OR FOR US OLD GUYS Megacycles lol lol that can Aline close to there’s again I just use this for reflective power
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
mvus-list mailing list
mvus-list@lists.febo.com
http://lists.febo.com/mailman/listinfo/mvus-list_lists.febo.com
Hi Tom,
I have been wanting to come for years, maybe this is the year.
Will you guys be doing antenna measurements? At 70cm? If so, I would
like to bring my homebrewed yagi with me.
Jan N8CBX
On 7/19/2019 12:48 PM, Tom Holmes via mvus-list wrote:
Jan...
You need to come out to the picnic!
From Tom Holmes, N8ZM